UHF Female Angle Bulkhead connector

Specifications

Interface Type UHF threaded (PL-259 / SO-239)
Impedance 50 Ohm (non-constant)
Frequency Range DC – 300 MHz
VSWR 1.20:1 typ. at 100 MHz
Insertion Loss 0.10 dB typ.
Contact Resistance ≤3 mΩ
Dielectric Withstand 500 VRMS
Mating Cycles 500 cycles
Body Material Brass, silver or nickel plated
Contact Material Brass, silver plated

UHF Female Angle Bulkhead Connector

UHF Family

The UHF connector (also known as PL-259 male / SO-239 female) is a large, low-cost RF connector designed in the 1930s for HF and VHF frequencies. Despite its name, its practical usable range is below 300 MHz due to its non-constant impedance design. It remains extremely popular in amateur radio (HF through VHF), CB radio, and marine radio applications.

Typical Applications

Amateur (ham) radio HF/VHF/UHF transceivers, CB radio, marine VHF radio, antenna switches and coax relays.

Gender & Polarity Note

This is a Female connector — it has a socket that accepts a male center pin. Female connectors are commonly used as panel-mount chassis connectors and bulkhead adapters.

Cables Available with UHF Female Angle Bulkhead

Select a cable type to see all connector pairings and pricing.

RG174

.1 INCH • DC – 3 GHz

RG316

.1 INCH • DC – 6 GHz

RFC100A

.1 INCH • DC – 6 GHz

RFC195

.195 INCH • DC – 6 GHz

RFC240

.240 INCH • DC – 6 GHz

RG405

.086 INCH • DC – 20 GHz

RG405_BLUE

.086 INCH • DC – 20 GHz

RG402

.141 INCH • DC – 20 GHz

RG402_BLUE

.141 INCH • DC – 20 GHz

RG58

.195 INCH • DC – 1 GHz

LMR195 Times

.195 INCH • DC – 6 GHz

LMR240 Times

.240 INCH • DC – 6 GHz

RG142

.195 INCH • DC – 6 GHz

RG400

.195 INCH • DC – 6 GHz

RG316DS

.1 INCH • DC – 6 GHz

LMR100 Times

.1 INCH • DC – 6 GHz

LMR240 ULTRA FLEX Times

.240 INCH • DC – 6 GHz

RFC240 ULTRA FLEX

.240 INCH • DC – 6 GHz

LMR200 Times

.200 INCH • DC – 6 GHz

RGU178

.06 INCH • DC – 6 GHz

Frequently Asked Questions

What frequency range does the UHF Female Angle Bulkhead connector support?

UHF connectors are rated DC – 300 MHz. The effective upper frequency of a cable assembly is limited by the lowest-rated component — either the cable or the connector. Always verify both are within spec for your target frequency.

How many times can a UHF connector be mated and unmated?

UHF Female Angle Bulkhead connectors are rated for approximately 500 mating cycles. Exceeding this can cause wear on the contact surfaces, increasing insertion loss and VSWR. For applications with very frequent connects and disconnects, consider a connector rated for higher cycle counts.

What torque should I use to tighten a UHF connector?

Use a torque wrench and follow the connector manufacturer's recommended torque specification. Hand-tight plus a quarter turn is a safe starting point for most push-on connectors.

Are the UHF connectors on CoaxRF assemblies weatherproof?

Our standard cable assemblies use high-quality connectors suitable for most indoor and sheltered outdoor applications. For fully weatherproof outdoor installations, we recommend applying self-amalgamating tape over the connector junction to prevent moisture ingress.

Do CoaxRF cables with UHF Female Angle Bulkhead connectors ship assembled and tested?

Yes. Every cable assembly — including those terminated with UHF Female Angle Bulkhead connectors — is hand-assembled and continuity tested before shipping. Cables ship free within the US from our US facility.